Rovertech 2.0

I hope he found that left handed screw driver you needed too , LOL. also the the barber shop paint to pinstripe over that tartan paint.

Hey mate , I have a few 220's and im in auckland. where abouts are you ?

Heres one of my 220's

Just fitted one of these to my coupe , seems to be working good. nice and easy install

unplug battery and leave off for 15 - 20 mins before starting the job after that disconnet yellow srs plug from under the steering column , then on the back of the steering wheel should be 2 or 3 screws which are normally torx or hex headed which have to undone to release the airbags and remove/hand...

Im not quite sure on what my C/R is because I didn't have enough time to test heads cc's , But the head had a light skim (I think the first ever), the block had 0.25" Thou off and the O pistons were kept the same just de-coked. I'll check next time it blows a HG or when I next take the head off...

Last week i just put my Coupe on the dyno with my M/O combo engine in it (which had still only covered 550 km's) and that pulled 121 Kw at the front hubs. Thats with a Gti-R T28 , Fmic with 2.5" piping and with standard exhaust and cat , The boost peaked at 12.6 psi then dropped to 10.5 - 11.5 ...

The Top bearings with the c ring notch can still be obtained in steel format, they are all stocked honda gearbox item lines , I managed to source most of the bearings from the usa from honda part suppliers.

I'll say 240 Hp at the fly just to be different , make sure you take some vids and pictures of it all running so we can see whats happening for when you post - HELP only 195 hp at the flywheel (sorry couldn't resist)

The integra type r is a great car to start off with , it handles its easy to work on and maintain and being a honda it will take a thrashing and will be reliable as fook. I also have a 1997 prelude type s (dyno read 124 kw at the front wheels) and that does shift for a heavy car but it feels like a ...

ok I was mistaken , it is the disco mpi

Have a look at this post and look about 1/3 of the way down

http://retrorides.proboards.com/index.c ... 47&page=18

I am pretty certain its the Freelander MPI , unsure what year though and ive only ever seen 1.

Yeh, I couldnt source these bearings from New Zealand (well I could but would of cost $252 each) so had to get them from the states for about $28 usd each.

ah yeh , well I found quite a few places to get these and I think $5 extra over the Polymide caged ones better to be safe than sorry

Sorry for the delay , been busy building up my engine. Heres the best pitures I managed to take (stupid camera focus and MUST have flash to get a clear picture or else its ALLWAYS blury) http://i1214.photobucket.com/albums/cc490/o0o0oo000o/PICT2692.jpg http://i1214.photobucket.com/albums/cc490/o0o0o...

Yeh , Tbh i can't believe no body has found them before.

Just thought people might like to know that I have found some Steel caged Versions of the roller bearing that goes at the bottom of the output shaft, I will load some pictures up later.

All of the DOHC Vtec engines are GREAT engines and even the Sohc Vtec D15b is a hoot, you can thrash them all day any day and they will happily take it. Just had a quick look on the NZ auction site and found 1 in minutes , If you look the top turrets look quite square Just like the white one http://...

Truly awesome , love the clean engine bay

I dont think the coupe can wear anything carbon fibre tbh and i think that the dc5 spoiler is a bit to round for the coupe,make sure the spoiler will fit the bootlid first.

Im in the process of fitting an evo 7 spoiler to my coupe and it fits the boot perfecty.

LOL how could u not notice a bumper being ripped off unless it was only cable tied on ...

stage 1 45Nm
stage 2 70Nm
stage 3 then 90°

shown on T series rebuild manual

79

Shame about the qustions being aimed at our larger cousins

15s cars VVC mini - 1996 metro 1.6 - 15.3 @ 87mph (avon park 2010) redvitesse -1996 vitesse sport 15.2@ 92mph (avon park 2011) matt077 - 2000 Rover 25 T16 turbo - 15.1 @ 97mph (psi at 8psi) (avon park 2009 - 1st time ever!) o0o0oo000o - 1994 Rover Coupe Turbo - 15.1 @ 148.8KMH (9psi ish) (Meremere d...