Wanted forged T16 turbo bottom end

charliecosworth · Post by **charliecosworth** » Sun Jan 27, 2013 10:50 am

Looking for good forged engine, I have already ported gas flowed head so willing to just buy bottom end ideally with forged rods too or wouldn't mind good engine set up that i could just bolt my head on to.
willing to travel to collect

MG Maestro Turbo T16

charliecosworth · Post by **charliecosworth** » Wed Feb 06, 2013 9:12 pm

still looking?

1234dist · Post by **1234dist** » Wed Feb 06, 2013 9:18 pm

Not that many around that arn't in use (storage) over winter. Gonna be past pol before people start waking them up.

edward22 · Post by **edward22** » Wed Feb 06, 2013 10:06 pm

just build one ...

Post by **Cableguy** » Thu Feb 07, 2013 8:11 am

I do forged bottom ends pretty cheap.

£300 for the build and £120 machine work.

You supply pistons and crank / gasket set.

For £1000 give or take a few pennies, it could be ready to fit.

Or for an extra couple of hundred quid I have one in my car I would sell, complete with head bolted on already and can be seen running.

charliecosworth · Post by **charliecosworth** » Sun Oct 20, 2013 7:43 pm

still looking for one if anyone thinking of selling?

higher the spec the better!! cash waiting

sihorton · Post by **sihorton** » Mon Oct 21, 2013 8:49 pm

I'm not promising, but I know of one that "might" be available in about 4 weeks time.

Spec was:
86mm oversize Wossner pistons
Block professionally honed and bored for pistons
Forged rods (can't remember exact brand)
Brand new crank
Brand new big end and main bearings
Brank new oil pump
Brank new gaskets
Alloy sump

Run only on millers 10/60 CFS oil
Will have done no more than 150miles since build and will have images and some receipts.

If it's available, it will be £1000.
Let me know if that's the sort of spec your looking for and i'll come back to you if it becomes available.

BTW, if it is available, I know other parts will become available which might be of interest if your looking for a good full package.

Si

charliecosworth · Post by **charliecosworth** » Mon Oct 21, 2013 9:02 pm

sihorton wrote:I'm not promising, but I know of one that "might" be available in about 4 weeks time.

Spec was:
86mm oversize Wossner pistons
Block professionally honed and bored for pistons
Forged rods (can't remember exact brand)
Brand new crank
Brand new big end and main bearings
Brank new oil pump
Brank new gaskets
Alloy sump

Run only on millers 10/60 CFS oil
Will have done no more than 150miles since build and will have images and some receipts.

If it's available, it will be £1000.
Let me know if that's the sort of spec your looking for and i'll come back to you if it becomes available.

BTW, if it is available, I know other parts will become available which might be of interest if your looking for a good full package.

Si

yes keep me posted, don't need the head has i have one ported and gas flowed with piper cams, which am sending back for bigger valves to be fitted.

charliecosworth · Post by **charliecosworth** » Sun Nov 10, 2013 10:53 pm

sihorton wrote:I'm not promising, but I know of one that "might" be available in about 4 weeks time.

Spec was:
86mm oversize Wossner pistons
Block professionally honed and bored for pistons
Forged rods (can't remember exact brand)
Brand new crank
Brand new big end and main bearings
Brank new oil pump
Brank new gaskets
Alloy sump

Run only on millers 10/60 CFS oil
Will have done no more than 150miles since build and will have images and some receipts.

If it's available, it will be £1000.
Let me know if that's the sort of spec your looking for and i'll come back to you if it becomes available.

BTW, if it is available, I know other parts will become available which might be of interest if your looking for a good full package.

Si

any news??

Deckz · Post by **Deckz** » Mon Nov 11, 2013 12:50 am

Posted by: BLACKSHADDOW

Got a bottom end here
Arrow rods
Je 86mm pistons
Steel billet crank
£3000

Post by **Cableguy** » Mon Nov 11, 2013 10:15 am

Deckz wrote:Posted by: BLACKSHADDOW

Got a bottom end here
Arrow rods
Je 86mm pistons
Steel billet crank
£3000

Diamond encrusted ?

rovermadman4825 · Post by **rovermadman4825** » Mon Nov 11, 2013 10:36 am

Have you not seen what josh is offering?

Post by **Cableguy** » Mon Nov 11, 2013 10:42 am

I am stumped at how £1000 for a brand new forged engine goes overlooked

Post by **Marty** » Mon Nov 11, 2013 11:01 am

Cableguy wrote:I am stumped at how £1000 for a brand new forged engine goes overlooked

To expensive you should know people on here by now

joshreynolds · Post by **joshreynolds** » Mon Nov 11, 2013 12:08 pm

rovermadman4825 wrote:Have you not seen what josh is offering?

He offered £1200

InB4Mike · Post by **InB4Mike** » Mon Nov 11, 2013 1:25 pm

Ought for nought

charliecosworth · Post by **charliecosworth** » Mon Nov 11, 2013 1:52 pm

Thought £1200 was good price for something never build up and still needs pistons buying for it, might be good buy at 1500 just the added cost getting it built up

Post by **Cableguy** » Mon Nov 11, 2013 1:59 pm

charliecosworth wrote:Thought £1200 was good price for something never build up and still needs pistons buying for it, might be good buy at 1500 just the added cost getting it built up

Its got the pistons with it for 1500.

joshreynolds · Post by **joshreynolds** » Mon Nov 11, 2013 2:01 pm

No pistons I'm afraid

joshreynolds · Post by **joshreynolds** » Mon Nov 11, 2013 2:03 pm

I can supply rave aswell to help build it yourself

Post by **Cableguy** » Mon Nov 11, 2013 2:03 pm

Must have misread it then, odd.

Anyway, good luck keeping it all if that is the case

Rovertech 2.0

Wanted forged T16 turbo bottom end

Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end

Re: Wanted forged T16 turbo bottom end